Why Adding A Replacing Upvc Window Handles To Your Life Will Make All The Different
Replacing uPVC Window Handles
It is simple to change the handles on windows made of Upvc. It is essential to ensure that the replacement handle is fitted into the spindle cutout in the window mechanism.
If you follow the steps below the handle of any cockspur will fit on most windows. repairmywindowsanddoors of the handle is key.
What to Look for
As time passes, uPVC handles on many windows in the UK begin to show signs of wear and tear. If this occurs, the window handle may become loose or difficult to operate, making it essential to replace it. Anyone who is comfortable using a basic hand tool is able to complete this task.

The first step is to make sure that the handle is securely fixed to the frame of the window in its open position. Next, locate the screws or pins that secure the handle in place. These are typically located on the inside of the handle. They can be removed with a screwdriver or pliers.
When the handle is loose, gently pull it away from its hinges. Then, you'll have to locate a replacement handle in the same size and style. This can be done at the DIY store or on the internet. The procedure should take just five minutes and a screwdriver.
The most important thing to consider when replacing the uPVC window handle is the step height. This is the distance from the bottom of the handle to where it is placed on the frame of the window. This is usually an accepted measurement, however it is crucial to check the step height of your existing handle before ordering a new one.
Depending on the kind of handle you choose There are various sizes that are available. Inline handles are offered for uPVC windows with lug centres of 31mm while cockspur handles have centers of lugs of 43mm. Tilt-and turn handles are typically found on uPVC Windows. They have a specific design that allows the window to be slid down to let in air and then rotated to fully open the window.
The most frequent uPVC handle breakage is internal cracking, rather than a breakage from the base. This could make it difficult to open. It is essential to make sure that any replacement handle is fitted with the same spindle that was used in your original one.
Remove the Old Handle
Incorrectly fitted or damaged window handles may cause your double glazed windows to close or open in a way that isn't correct and may result in them getting stuck. This could be due to many factors, such as general wear and tear on the metal handle or corrosion. In these cases it is essential to replace the window handle as promptly as you can to prevent further damage or loss of function.
When replacing upvc windows handles it is recommended to remove the old handles from the window. To do this, begin by taking off the screw that is covered when the handle is in its closed position. This should reveal another screw that once removed, you are able to begin to remove the handle itself. You can make the job easier by using an electronic screwdriver.
It is also important to note that the screws on the handle may be hidden behind caps made of plastic, so it is a good idea to take the Stanley knife to the screws and take them off. After removing the handle, you will have to examine the square cutout on the base to make sure that the new handle you choose for the window lock is compatible. This is important as you will need to measure the length of the spindle on the previous handle to ensure it is in line with the size of the window mechanism and the handle spindle that has been cut out.
The different types of window handles made of upvc are: Espag handles, which feature a central screw that can be turned left or right; Cranked handles, that have two screws and are used on tilt and turn windows made of upvc; and Spade handles, which have an arm that is flat and can be used on either side of the window. Once you have a suitable replacement, it's just a matter of screwing the handle into position and ensuring that the spindle is fitted into the lock mechanism. After that then it is time to secure it to the window frame and the replacement window handles made of upvc should be secure.
Take a measurement of the Spindle
If you're replacing a upvc window handle that has come off, it's likely because the spindle that holds it in place has become loose or damaged. In certain situations, you can tighten the spindle using pins or screws. In other cases it will have to be replaced completely. There are a few different kinds of window handles made from upvc. There are three types of handles: inline espagnolette, tilt-and-turn, and cockspur. Each kind has a distinct method of installing and removing the handle.
Before purchasing a replacement handle it is essential to know the size of the one you have. This will help ensure that the new handle is the right size and fits into the window. Fortunately, all handles adhere to industry standard sizing so it's relatively easy to identify the correct size.
To measure the size of the handle move the window to the open position. Then, you should be able to see the size of the screw or pin that secures it. Use a ruler or tape measure to determine how long the spindle is. Once you have the length of your spindle it is possible to buy a replacement of the exact same length.
The step height of a window handle is also important to consider when purchasing a replacement. The step height is measured from the base to the point at which the handle sits on the frame. Typically, this will be around 21mm for uPVC windows, and 9mm for aluminium. To be sure that the new handle is suitable, you can drop something into the gap to see how far it extends before meeting an obstruction.
Cockspur handles usually have different backset heights, based on the style of window they're installed in. Inline Espag handles have a standard height of 43mm from centre to centre (2 fixing points). Cockspur handles have different backsets, based on which window design they are in. This is because they have a spur which extends from their handle and locks onto a cockspur wedge striking plate.
Fit the New Handle
Once you've selected the new handle, make sure it is aligned with the screw holes on the door. Then, secure it with the screws supplied. If you're also replacing the latch lever it can be put in in a similar way to the door handle. After that, attach the door trim again to hide the mounting screws.
Tips: To remove the metal head from a wooden wedge, place the handle on the floor, so that its wide end is level with the ground. Then, use a hammer and tap the thin end. Be careful not to scratch the handle or spindle.